Three Ply & 5 Ply Automatic Paper Corrugated Board Machinery
Hydraulic Shaftless Mill Roll Stand
We are leading supplier of Hydraulic Shaftless Mill Roll Stand.
- The structure is double rotary shafts with four arms; Support two paper mill rolls on both arms at the same time.
- Hydraulic control for paper mill roller up-down, clamp open and centering. Or motorized clamp open and centering.
- It is suitable for cutting 2 ply sheets and paper of any GSM quality.
- Using multi-point brake which imports from Italy and automatic expansion springiness chucks, Reduce paper waste
ECONOMICAL MODEL 5 LAYER MACHINE
|Minimum Order Quantity||1 Set|
We offer Corrugation Plants that are designed and fabricated to meet the requirements of different industries. Reduces production cost manifold. These machines offer ultra modern on line 3/5 ply paper corrugated board making plant. Assured quality with unmatched service back up.
5 ply corrugated box making plant High speed bearing mounted corrugation machine with variable speed drive- 2 nos. Drum type heaters - 4 nos. Self loading reel stand- 5 nos. Triplex heating unit before gluing On line duplex pasting unit Heating cooling and drying chamber (consist of fourteen hot plates) Heavy duty pull unit On line creasing and slitting unit Heavy duty cut off unit 3 ply corrugated box making plant High speed bearing mounted corrugation machine with variable speed drive Drum type heaters - 2 nos. Self loading reel stand- 3 nos.
Duplex heating unit before gluing On line simplex pasting unit Heating cooling and drying chamber (consist of nine hot plates) Heavy duty pull unit On line creasing and slitting unit Heavy duty cut off unit the plants above include complete fabrication and synchronization of all machines together. Overhead bridge and conveyor take up belts. Motorized web adjustment unit, gangway and stairs
Double Facer Corrugation Machines
The double facers offered by us are used to make perfectly bonded board. The liners are heated and transported to the double facer free of stress due to the pre-conditioner. The hot plates stay completely flat for steady heat transfer over the entire working width without edge crush in all operating conditions. Different numbers of hot plates can be configured in heating section according to requirements of our clients. Further, the pressure rolls of cooling section make sure perfect forming quality. The specially designed feed geometry aid in eliminating bubbles & ripples in the liner and conditions it prior to bonding. Designed to have low friction properties, these facers are highly corrosion resistant.
Flow of steam/oil within the Hot Plates ensures even heat transfer across the full surface and minimum loss of energy
Pressure rolls can be adjusted in micron individually depending upon the grade of board & speed of production
The upper and lower Double Facer Belts are synthetic
The belt is mechanically or pneumatically lifted from the hotplates when the machine stops
Rubberized /M.S. Puller Rolls are used
The upper and lower belt drums are driven by synchronizing with cut-off
The drive rolls are wrapped with double helically grooved rubber, in order to increase the traction of belts
Mechanical Shaftless Mill Roll Stands
Single Side Load-1500kg
Paper Roll Length Scope-900mm-1600mm
Pneumatic Fingerless High Speed Single Face Corrugation Machine
Product Details:The machine offershigh rate of production and enhance efficiency.The corrugated flute rollers,pressure rollers and glue rollers are by Pneumatic adjustment. The flute rollers are mounted on bearings for smoothrunning and imparts proper impression on paper.The middle flute roller is fitted with vaccumsuction jacket instead of adapters which keep flute profile stable.
- Design Speed SF-260E- 50MTRS/MIN
- Design Speed SF-280E - 60MTRS/MIN
- Design Speed SF-260S- 60MTRS/MIN
- Design Speed SF-280S- 80MTRS/MIN
- Design Speed SF-320S- 120MTRS/MIN
Motor Required: (H.P)-- 7.5/7.5/3 (FOR 52* MC)
Simplex Gluer Machines
Power motors and electrical parameters:
- Glue roller initiative frequency motor: 3 kW 380 V 50 Hz continuous (s1) working standard
- Glue amount adjustment reducer: 250 W 380 V 50 hz short s2 working system
- Pressure roller gap adjustment motor: 250 W 380 V 50 Hz short s2 working system
- Glue pump motor: 2. 2 kW, 380 V 50 Hz continuous s1 working system
- High Pressure Pre-heating drum dia 470mm/600/900mm for Liner of medium as per speed of machine
- Wrap Roll: Fixed for low speed and adjustable motorized for high speed plant for adjustment of pre heating area
- Brake is equipped for pre-heating roll to adjust Web Tension
- The Pre-heater roll can be equipped with spray to adjust moisture contents of the paper. It is optional feature
- Fixed Rotational cylinders are available on choice
- Available Width: 1200-2200mm
- Adopted on the 16th channel welded, electric adjustment of cardboard the size of the lateral output pneumatic control board electrical adjustable conveyor speed
- Vertical bin using wide flat belt conveyor transport
- Cardboard sheets to the desired number or height requirements will be controlled foot switch of cardboard.
The maximum accumulation length : 3000mm
The maximum stack height : 200 mm
Main conveyor motor : 3kw
Lateral output of the motor : 1.5 kw.
Walking motor :1.5kw
Three phase- asynchronous motor.